Construction Tools

BNR001-120 and BNR001-140
Diameter 120 mm (4.75”) or 140 mm (5.50”)
Overall length 60 cm (24”)
Designed for plasters, adhesive mortars, mortars, tile adhesives and fillers, best for sticky and viscous materials
Material Flow Bottom to Top
Connection M14 x 2 male threads.

BNR002-57
Diameter 57 mm (2.25”)
Overall length 13.5”
Designed for paints, lacquers, thin coatings, and ready-mix plaster. Use on BN6169 or drill.
Material Flow Top to Bottom
Connection 5/16” hex shank.

BNR003-120 and BNR003-140
Diameter 120 mm (4.75”) or 140 mm (5.50”)
Overall length 60 cm (24”)

Designed for concrete, mortars, plasters, heat-insulating plasters, and epoxy resin with sand, best for heavy and high viscosity materials.

Material Flow Top to Bottom
Connection M14 x 2 male threads.

BNR004-120 and BNR004-140
Diameter 120 mm (4.75”) or 140 mm (5.50”)
Overall length 60 cm (24”)

Designed for thinset, tile adhesive, grout, adhesive mortars, ready-mix mortars, and pointing mortars, and fillers, best for small volumes on high speed mixers.
Material Flow Bottom to Top
Connection M14 x 2 male threads.

 

BNR005-120
Diameter 120 mm (4.75”) or 140 mm (5.50”)
Overall length 60 cm (24”)
Designed for plasters, adhesive mortars, tile adhesive and fillers, best for sticky and viscous materials.
Material Flow Bottom to Top
Connection M14 x 2 male threads.

BNR006-100
Diameter 100 mm (3.875”)
Overall length 60 cm (24”)

Designed for paints, lacquers, glazings, primers, and paste, best for small volumes of low viscosity materials.
Recommended to use on BNR6169.
Material Flow Top to Bottom
Connection M14 x 2 male threads.

BNR008-120

(paddles sold in pairs left & right)

Diameter 120 mm (4.75”)
Overall length 60 cm (24”)

Designed for concrete, cement, mortars, and grouts with aggregate less than 3/8” diameter. Also for gypsum lime plaster, fibrated aluminum roof coatings and paints. Not for highly viscous materials.
Material Flow Top to Bottom
Connection 13 mm or ½” Hex Shank, for BN6402A mixer.

BNR009-120 and BNR009-140
Diameter 120 mm (4.75”) or 140 mm (5.50”)
Overall length 60 cm (24”)

Designed for fillers, bitumen coatings, joint cement, epoxy-resin compounds, and grouting compounds, best for prevention of lump formation and lessens adding air into the mixture.

Material Flow Parallel
Connection M14 x 2 male threads.

BNR010-120 and BNR010-140
Diameter 120 mm (4.75”) or 140 mm (5.50”)
Overall length 60 cm (24”)

Designed for gypsum-lime plaster, fibrated aluminum roof coatings, and paints. This paddle can be disassembled in two pieces and fit into a carrying case.
Material Flow Top to Bottom
Connection M14 x 2 male threads.

BNR011-120 and BNR011-140
Diameter 120 mm (4.75”) or 140 mm (5.50”)
Overall length 60 cm (24”)

Designed for paints, lacquers, glazings, primers, and paste. This paddle can be disassembled in two pieces and fit into a carrying case.
Material Flow Top to Bottom
Connection M14 x 2 male threads.

 

 

 

 
  Benner-Nawman (1925) \ n:       1. Best quality products engineered with intelligence and imagination
2. Construction tools: Rebar Benders and Cutters  3. Specialty Hand Tools   4. Low Voltage Enclosures
Use of the BNProducts website and our organization information constitutes acceptance of our Terms and Conditions.
© 2006 - 2010 Benner-Nawman, Inc. All Rights Reserved. Call us: (800) 992-3833